collapse

Author Topic: Replacing bearings on diamond saw  (Read 469 times)

Gemmie

  • Newbie
  • *
  • Posts: 3
    • View Profile
    • Email
Replacing bearings on diamond saw
« on: September 21, 2018, 05:34:09 PM »
The bearings on my Robilt diamond saw need replacing but I can't get the shaft out! Is there a trick to it? Any advice welcome, thanks, Gemmie.

Rusted

  • ALF'er Platinum
  • *
  • Posts: 321
    • View Profile
    • Email
Re: Replacing bearings on diamond saw
« Reply #1 on: September 22, 2018, 07:32:32 AM »
Probably no trick, they are just well engineered so the bearings are a press fit, meaning you will need a hydraulic press to get them off.
Dont belt them with a hammer, you will mushroom the end of the shaft and cause yourself a lot of grief.

Dismantle as much as you can, see if you can get a number off the bearings and buy a new set, then take the lot to an engineering shop and get them to press the old ones off and the new ones on.

Gemmie

  • Newbie
  • *
  • Posts: 3
    • View Profile
    • Email
Re: Replacing bearings on diamond saw
« Reply #2 on: September 23, 2018, 01:17:23 PM »
Thanks Rusted! All I can get off is the pulley. Can see the outer bearing and number but likely it will have a bearing on the inside as well, no idea what that looks like. Then there is a bush on the inside, the diamond blade rests against that. If I hold this bush with pliers, I can only just turn the axle by hand but the bush won't move sideways.

Rusted

  • ALF'er Platinum
  • *
  • Posts: 321
    • View Profile
    • Email
Re: Replacing bearings on diamond saw
« Reply #3 on: September 23, 2018, 03:13:24 PM »
Buy two of the bearings by the number you have. I doubt very much if Robilt would have used odd sized bearings for each end.
Most sizeable towns have a bearing shop.

Clean up any rust /paint or crud on the shaft with a bit of wet and dry, also the raised pimple where the grub screw from the pulley marked the shaft. Probably need to gently file that.

Next take the shaft and housing to an engineering shop, it probably won't take much under a press to get everything to pieces.

Replace both bearings even if you think one sounds OK, they usually do until they are placed under load.

Robol

  • ALF'er Bronze Member
  • *
  • Posts: 5
    • View Profile
    • Email
Re: Replacing bearings on diamond saw
« Reply #4 on: September 23, 2018, 05:17:50 PM »
When I replaced mine I bought a bearing puller from Supa Cheap Auto. I bought the large one for around $25.00. I suggest you mark the shaft at the edge of the bearing. If I had done that it would have saved some messing around when it was going back together.

Gemmie

  • Newbie
  • *
  • Posts: 3
    • View Profile
    • Email
Re: Replacing bearings on diamond saw
« Reply #5 on: September 24, 2018, 05:57:03 PM »
I had another go today and to my surprise I could move the bush over using a big screw driver and that's when I could see the circlip on the axle, right against the inside bearing. Very hard to get off!!
Carefully tapped the axle out with outside bearing still attached, then tapped out the inside bearing and after a trip to town and $23 later, brand new bearings and new circlip.
Outside bearing glued in for good measure!

Rusted

  • ALF'er Platinum
  • *
  • Posts: 321
    • View Profile
    • Email
Re: Replacing bearings on diamond saw
« Reply #6 on: September 24, 2018, 07:24:56 PM »
Excellent news Gemmie.


Tags:
 

* Sponsor

HTML Online Editor Sample

ALF is hosted by Aussie Sapphire as a free service to the Lapidary community.

Visit our website here
Phone 1800 50 21 40
Or find us on Facebook

Recent Activities

Dangerous minerals by Plutonium
[January 19, 2019, 10:24:54 PM]


403 errors by MakkyBrown
[January 19, 2019, 10:04:23 PM]


Math Formula by MakkyBrown
[January 19, 2019, 09:21:13 PM]


Snake Catching by Sandbagger
[January 19, 2019, 08:26:45 PM]


Is Grabben Gullen dead? by Sandbagger
[January 19, 2019, 07:03:27 PM]


Changing Ball-Bearing on the left side of DP Pixie by olaf
[January 19, 2019, 12:14:16 AM]


Heading to Gemtree & Harts Range by Jamo
[January 18, 2019, 10:06:49 PM]


Any geologists out there? by harryopal
[January 18, 2019, 12:09:53 PM]


Areas around colac by MakkyBrown
[January 17, 2019, 08:53:22 PM]


Crystal structures by harryopal
[January 15, 2019, 04:28:00 PM]


What scales for weighing gold? by Sandbagger
[January 13, 2019, 11:41:38 PM]


Mt Gambier- South Australia Fossicking by Rusted
[January 12, 2019, 03:58:19 PM]

* Calendar

January 2019
Sun Mon Tue Wed Thu Fri Sat
1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
[20] 21 22 23 24 25 26
27 28 29 30 31

No calendar events were found.
Sorry! There are no calendar events available at the moment.

* Who's Online

  • Dot Guests: 74
  • Dot Hidden: 0
  • Dot Users: 0

There aren't any users online.

* Find us on Facebook

* Forum Stats

  • stats Total Members: 3825
  • stats Total Posts: 54061
  • stats Total Topics: 5757
  • stats Total Categories: 6
  • stats Total Boards: 27
  • stats Most Online: 160