collapse

Author Topic: "Diamond Nine" cut in citrine  (Read 732 times)

RoughCreations

  • ALF'er Silver Member
  • *
  • Posts: 85
    • View Profile
    • Rough Creations homepage
    • Email
"Diamond Nine" cut in citrine
« on: December 05, 2020, 03:48:35 PM »
Showing off my recently completed 27.2ct Tasmanian Gladstone citrine.
"Diamond Nine" Fusion-style cut taken from Andrew Brown's Faceting Design book (Volume 1).

https://youtu.be/ArrIj2DO_Z0

https://youtu.be/5woIm3EHeuc

RC.
« Last Edit: December 05, 2020, 04:46:09 PM by RoughCreations »
Rough Creations - Beauty from rough beginnings

Faceting Frank

  • ALF'er Gold Member
  • *
  • Posts: 179
    • View Profile
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #1 on: December 05, 2020, 04:33:33 PM »
Very impressive, what did you polish it with, Diamond or Cerium?

RoughCreations

  • ALF'er Silver Member
  • *
  • Posts: 85
    • View Profile
    • Rough Creations homepage
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #2 on: December 05, 2020, 04:38:21 PM »
Thanks, used some cerium on an old Darkside lap. Slow rotation, good quality A-grade 2 micron white cerium oxide polish powder from Aussie Sapphire.
Rough Creations - Beauty from rough beginnings

harryopal

  • ALF'er Gold Member
  • *
  • Posts: 225
    • MSN Messenger - harryopal7@gmail.com
    • View Profile
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #3 on: December 06, 2020, 07:59:21 PM »
It looks to be flawless. How do you rate the cut?
harryopal

MakkyBrown

  • Global Moderator
  • ALF'er VIP
  • *****
  • Posts: 1323
    • View Profile
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #4 on: December 06, 2020, 08:01:17 PM »
Very nice mate, these big stone fusion designs you are cutting are very impressive.

Bucket

  • ALF'er VIP
  • *
  • Posts: 955
    • View Profile
Re: "Diamond Nine" cut in citrine
« Reply #5 on: December 07, 2020, 08:00:21 AM »
Makky, the more I see of your designs the more I'm liking them, I have your books on my Christmas list. Rough Creations, looks really great, great finish!
Common sense isn't exactly common

Faceting Frank

  • ALF'er Gold Member
  • *
  • Posts: 179
    • View Profile
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #6 on: December 07, 2020, 08:12:53 AM »
What grade diamond did you use before polishing? 

RoughCreations

  • ALF'er Silver Member
  • *
  • Posts: 85
    • View Profile
    • Rough Creations homepage
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #7 on: December 07, 2020, 09:41:07 AM »
Hi Frank, I used a 200# ebonite diamond disk, followed by an 800# ebonite diamond disk.
I have discussed the ebonite disks in detail in other posts.
The Fusion designs seem to work in various RI ranges really well, there is a lady on Instagram from Melbourne cutting some amazing Fusion sapphires: https://www.instagram.com/pebblesprout/
I have only tried quartz so far - my Instagram page: https://www.instagram.com/roughcreation/
RC
Rough Creations - Beauty from rough beginnings

RoughCreations

  • ALF'er Silver Member
  • *
  • Posts: 85
    • View Profile
    • Rough Creations homepage
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #8 on: December 07, 2020, 09:43:28 AM »
Very nice mate, these big stone fusion designs you are cutting are very impressive.
Thanks, I don't understand why they work so well in humble old quartz, but you seem to get a weird 3D star coming at you!
Rough Creations - Beauty from rough beginnings

RoughCreations

  • ALF'er Silver Member
  • *
  • Posts: 85
    • View Profile
    • Rough Creations homepage
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #9 on: December 07, 2020, 09:59:59 AM »
It looks to be flawless. How do you rate the cut?
The stone itself is effectively flawless (inclusions hard to find under 10x loupe). The cut is very straightforward, with only 13 crown facets and 24 pavilion facets. With big stones like this (21mm across the widest flats) a level of cheating happens, small inaccuracies in the machine are magnified.

See the Diamond Nine pavilion below:



Look at it carefully - see the asymmetry of it?
This must be part of the hocus-pocus of the Fusion designs.
Rough Creations - Beauty from rough beginnings

Faceting Frank

  • ALF'er Gold Member
  • *
  • Posts: 179
    • View Profile
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #10 on: December 07, 2020, 10:44:59 AM »
Hi Rough Creations, went through your thread again about Ebonite laps. I can see the finish they produce is far finer for the grit size than a normal bonded diamond lap. In fact look finer than 3k on a BATT lap. Great finish as a pre polish.

MakkyBrown

  • Global Moderator
  • ALF'er VIP
  • *****
  • Posts: 1323
    • View Profile
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #11 on: December 07, 2020, 11:20:22 PM »
The ebonite laps are basically like Nubond laps I think, great for soft material but may well cause orange peel on sapphire and harder materials especially the 800#. I'm about to test some Chinese resin laps and see how they go. Expecting them to be similar to the ebonite and Nubond.

Roughcreations you are going to like volume 3, it has checker fusion ovals and a couple of other fusion designs. I've been really enjoying Pebblesprout cutting my design in sapphire. Beautiful cutting.
MB
« Last Edit: December 08, 2020, 09:09:39 AM by MakkyBrown »

Faceting Frank

  • ALF'er Gold Member
  • *
  • Posts: 179
    • View Profile
    • Email
Re: "Diamond Nine" cut in citrine
« Reply #12 on: December 08, 2020, 11:39:29 AM »
There’s a three page article about polishing quartz in the current Australian Facetors Guild facet talk. I haven’t read all of it yet, but one bit of advice that interested me was sanding your Lucite lap instead of scoring. I rip mine apart with a broken hacksaw blade and pile the pressure on when polishing with cerium.
So this is the opposite to what I do, the lap sanded with 800 grit wet and dry and light pressure when polishing.

Shifter55

  • ALF'er Bronze Member
  • *
  • Posts: 47
    • View Profile
Re: "Diamond Nine" cut in citrine
« Reply #13 on: December 10, 2020, 03:25:27 PM »
Thanks, I don't understand why they work so well in humble old quartz, but you seem to get a weird 3D star coming at you!
The pavillion tiers remind me of a round brilliant I saw in an article once - I think it was called NOMAG? Same bar-shaped mains.
Really that odd pavillion symmetry is doing a lot of work, you can almost always take them to steeper mains angles than even ones.

Tags:
 

* Sponsor

HTML Online Editor Sample

ALF is hosted by Aussie Sapphire as a free service to the Lapidary community.

Visit our website here
Phone 1800 50 21 40
Or find us on Facebook

Recent Activities

Unknown Faceting Machine by Rusted
[January 18, 2021, 12:18:12 PM]


Repair Big R double grinder by Zircon
[January 11, 2021, 12:09:21 PM]


Diamonds down by harryopal
[January 03, 2021, 12:56:04 PM]


Parts for polymetric faceting machines by Sharyn
[January 03, 2021, 11:57:07 AM]


Topaz Tec XT6 for sale by Dihusky
[January 01, 2021, 09:23:23 AM]


Trying to find value of Gemstone for my father by loscarlett1
[December 31, 2020, 06:12:46 PM]


Tell him he's dreamin by steve f
[December 31, 2020, 02:15:50 PM]


Finding rocks/gems in Whyalla south australia by Pete49
[December 27, 2020, 01:52:30 PM]


My book volume 3 by MakkyBrown
[December 26, 2020, 08:02:00 PM]


Cape Liptrap Prospecting by ev4n0ne
[December 21, 2020, 08:50:53 PM]


Hughes creek in Victoria by wallie
[December 21, 2020, 03:01:37 PM]


Hi People, a newbie on all fronts... by digitaus
[December 16, 2020, 07:37:57 PM]

* Calendar

January 2021
Sun Mon Tue Wed Thu Fri Sat
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 [21] 22 23
24 25 26 27 28 29 30
31

* Who's Online

  • Dot Guests: 77
  • Dot Hidden: 0
  • Dot Users: 1
  • Dot Users Online:

* Find us on Facebook

* Forum Stats

  • stats Total Members: 4455
  • stats Total Posts: 56664
  • stats Total Topics: 6050
  • stats Total Categories: 6
  • stats Total Boards: 27
  • stats Most Online: 773