collapse

Author Topic: Gemmasta 4 faceting machine water issue  (Read 744 times)

hithwentinuviel

  • ALF'er Bronze Member
  • *
  • Posts: 7
Gemmasta 4 faceting machine water issue
« on: May 26, 2020, 12:42:37 PM »
Hi. Hi have a gemmasta 4 faceting machine and the water container has been leaking underneath near the screw attaching it to the machine. I tightened up the screw in the bottle which made the bottle stiff and not move. I thought the bottle rotated on the brass rod and that the brass rod underneath the bottle could be removed so you could empty the bottle however i am unable to remove the rod even after removing the plastic tightening screw that holds it to the machine
 Does the brass rod remove and do i just need to use some pliers to help move it or is it stuck to the machine?

Rusted

  • Global Moderator
  • ALF'er VIP
  • *****
  • Posts: 508
Re: Gemmasta 4 faceting machine water issue
« Reply #1 on: May 26, 2020, 01:17:24 PM »
I think I am getting the picture that the brass rod is frozen inside the support on the machine. Is that right?

The brass rod stays screwed tightly onto the the water container and (should) comes out of the support stand on the machine.

If the rod is frozen inside the support and wont come out you might need to spray some WD40 and let it sit for a few days, get your gas torch and give the outside of the support a bit of heat, then try and remove it with some pliers. Try not to mangle things too much. It might pay to remove the support bracket from the machine first, I think the hole goes all the way through so you might be able to gently tap it with a hammer and some sort of punch from the other end and get it to move.

If the water container is leaking unscrew the screw from inside the container, clean everything up, apply a bit of silicone sealant to the inside and outside parts and screw them all back together. The leak is probably what caused corrosion to freeze everything together.

hithwentinuviel

  • ALF'er Bronze Member
  • *
  • Posts: 7
Re: Gemmasta 4 faceting machine water issue
« Reply #2 on: May 26, 2020, 01:56:39 PM »
Thanks for your help

Tags:
 

Recent Activities

Gems stolen, Mt Surprise by starsapphire78
[September 14, 2021, 09:07:23 PM]


Joke of the Day by starsapphire78
[September 14, 2021, 09:03:58 PM]


Back after long layoff by Bucket
[September 14, 2021, 03:27:15 PM]


Springsure closed by Lyn
[September 11, 2021, 03:32:16 PM]


LEVEL GIRDLE ISSUE by RoughCreations
[September 09, 2021, 10:05:15 AM]


Malachite by Bucket
[September 08, 2021, 01:48:47 PM]


"Friable" diamond by Scratches
[September 08, 2021, 11:57:07 AM]


brain fade by harryopal
[September 04, 2021, 08:49:42 PM]


Making your own concave cutter mandrels by RoughCreations
[September 04, 2021, 01:08:50 PM]


Opal glue. by Bucket
[August 31, 2021, 05:21:21 PM]


Bevelled sides, flat top Cabochon by gill_rocks
[August 30, 2021, 04:56:40 PM]


Concave cutter variable oscillator. by Faceting Frank
[August 30, 2021, 08:11:01 AM]


cleaning polish lap by Glen edge
[August 29, 2021, 01:08:55 PM]


Pewter Lap build by RoughCreations
[August 25, 2021, 05:45:14 PM]


Halls Mark 3 by Glen edge
[August 20, 2021, 12:54:33 PM]